Durable and Reliable Single Shell Rotary Dryer for Coal Slime Drying Mineral Ore Processing Turnkey Service!

Conventional thermal sterilization is carried out through heat conduction, convection or radiation to heat the food surface to the inside. To achieve the sterilization temperature, it often takes a long time. Microwave sterilization is a direct interaction of microwave energy and food and its bacteria. The interaction between heat effect and non thermal effect is faster than temperature and sterilization. The treatment time is greatly shortened, and the sterilization effect of various materials is usually 3-5 minutes.

Durable and Reliable Single Shell Rotary Dryer for Coal Slime Drying Mineral Ore Processing Turnkey Service! of traditional Chinese medicine, also known as microwave traditional Chinese medicine dryer, microwave traditional Chinese medicine drying equipment, microwave medicine drying insecticidal, the same type of industrial microwave equipment, apply to heat-sensitive Chinese medicine, and valuable health herbs such as ginseng and other herbsdrying, sterilization processing.

Tunnel microwave herbs dryer is for drying and sterilizing medicinal materials and pills,for drying and sterilizing and heating materials in strip shape, cube shape,small&round shape,leaves type, powdery form as well as filter cake which have high water content and certain and certain viscosity. It is also used for sterilizing medicinal liquid before and after packing.

Single Shell Rotary Dryer for Coal slime drying

Coal slime from post-flotation concentrate, coal washing process or coal mining processes are of great recycling value and also environmentally necessary for recycling. Coal slime drying may adopt several different types of dryers lLD rotary dryer, fluid-bed dryer,etc. according to the state of coal slime and drying requirement; of which rotary dryers are most commonly installed in practice due to its effectiveness in manufacturing and operation cost.

Our factory has a long history in design and build of specialized rotary dryers for processing coal slimes in coal preparation plants.

The slime drying system mainly consist of rotary shell, combustion system, seating rollers, special designed internal breaking &cleaning devices, shell sealing and transmission devices, etc.. Fuel is adjustable to match each individual installation condition. The unparalleled advantage of this system is that it has a unique internal structure that can effectively break up big lumps of sticky coal and clean sticky materials off the lifters, thus increase heat transfer efficiency and achieve designed requirements on moisture content and granule sizes.

Considering the nature of coal slime, this dryer is divided into four drying zones: the first zone is buffer zone where wet slime enters into the dryer and contact with the hot air evaporating at high rate; wet feed are moved to the second zone with big angle lifters before sticking. The second zone is self-cleaning zone where wet slime move in cascade motion and is prone to stick to the shell while falling down from lifters. Specially designed self-cleaning device is installed to remove the shell sticking, meanwhile big lumps of sticky material is also scattered by the cleaning devices, this further increase heat transfer. The third zone is tilt lifter zone where the coal slime is in loose state with low moisture content, which is not sticky anymore. The forth zone is output zone where material slide to the output along with rolling shell. There are no lifters in this zone.

Main features:

1. Designed with high torque, high overloading capacity, low operation cost.

2. Concurrent drying to avoid possibility of ignition, higher evaporation rate due to hot combustion air and wet coal lime entering from the same side, lower exhaust air temperature and higher heat efficiency.

3. Operating parameters are adjustable to varied state of coal slime to ensure constant and stable cascade motion of material and increase heat transfer.

4. Upgraded feeding and discharging system to avoid possibility of feed clogging, interruptions, non-uniformity or reverting, and thus load of dust removing system is less.

5. Specially designed fligLD and breaking system further enhances its self-cleaning and heat transfer capability and outcome shell sticking problem, thus could handle varied materials with varied moisture content and viscosity (highly adaptable to ….)

6. Output sizes and moisture is controllable according to each individual customer’s demand. Dried coal slime moisture can be less than 8% and size below 8mm.

Technical data of rotary coal slime dryer

The moisture content is very important in determining the usability of coal for further technological processing. In coal, the moisture may be present in the form of surface or hygroscopic moisture. Surface moisture is not dependent on the coal type because it depends on the classification and washing processes performed in the coal mine and on the soaking process during transport and storage. The evaporation of surface moisture takes place in the first drying period at a constant drying rate. Hygroscopic moisture depends on the rank of coal; it decreases with the age of coal. The evaporation of hygroscopic moisture takes place in the second drying period at a falling drying rate.

Comparison Chart of Single Shell Rotary Dryers in counter current /co-current air flow

Counter current Rotary Dryer	Co-current Rotary Dryer

Working Illustration of two types of Rotary Dryers

Various FligLD Designs for Rotary Dryers when Drying different types of materials(Example: a is suitable for sticky material)

Different Types for FligLD Designs for Rotary Dryer	Cascade Motion of Materials in Rotary Dryer

To ensure that the dryer is loaded close to optimal, it is important to know the amount of solids that can be held up in the fligLDs. If they are underfilled, the dryer will be performing inefficiently, below its capacity. Excessive overload of the shell will result in a

proportion of the material transported by kiln action,and the contact with the hot gases is limited. The residence time of the solids will be reduced and the quality of the product may be unacceptable.

Please contact us for a suitable rotary dryer design for your material

1. Free consultation on technical &commercial issues, provide market evaluation, project feasibility based on each customers' condition.

2. Provide free drawings at no cost for factory layout, piping & wiring systeLD, installation plannings,

3. Free installation, commissioning and operation training services at no costs to customers.

4. 24/7 aftersales service, free of charge if repair service required within 1 year after installation.

Contact Person: Jayson
Company Name: Shandong Leader Machinery Co.,Ltd.
Telphone: 86-531-82633959 (Working Time)
86-18905316466(Nonworking Time)
Company Location: Leader Industrial Park,Jinan,Shandong
Contact Person: [email protected]